KBMM-225D KB Electronics 16 Amp SCR 115/230VAC Chassis Drive 90/180VDC Output 9451

KBMM-225D Is a 115/230 VAC rated 12 Amps RMS @ 45C. The control is designed for 90 & 180VDC PM & Shunt motors. It will control motors between 1/100-1.5 HP (3.0 HP w/aux. Heat sink) by inserting the proper Plug-in Horsepower Resistor®. Direct fit replacement for Baldor's P/N: BC142-6

KBMM Speed range is 50:1 with load regulation of 1%. Features include: AC Line fuse and Armature Fuse holder, Auto Inhibit®, Voltage Following, MOV transient protection, 5K speed pot and trimpot adjustments for Min, Max, Accel, Decel, IR and CL. Options include Auxiliary heat sink, Barrier Terminal Board, RFI/EMI filters and Signal Isolation (model SI-6). This control is available worldwide from stocking KB distributors. UL, CSA, CE. Patented. 

The KBMM-225D full-wave variable speed DC motor controls, now with SMT construction. The controls contain a unique, super fast, Direct-Fed™ current limit circuit that helps to protect the SCR power bridge against direct shorts. The reliability of the KBMM™ is further enhanced with the use of high-surge, 25A SCRs and AC line and armature fusing. The KBMM™ is fitted with KB’s exclusive Plug-in Horsepower Resistor®. It eliminates the need for recalibrating IR Comp and Current Limit when the control is used on various horsepower motors. The versatility of the KBMM™ is confirmed by its extensive list of standard features, such as: selectable armature or tach feedback and adjustment trimpots for Min speed, Max speed, IR comp, CL and linear Accel and Decel. The KBMM™ includes Auto Inhibit®, which eliminates surging during rapid AC line switching; pulse transformer triggering, which provides cogless operation at low speed; and superior noise rejection circuitry, which eliminates false starts and blown SCRs. Enable (N/C) and Inhibit (N/O) functions provide electronic switching of control output. The output voltage of the control is a linear function of potentiometer rotation. In addition, the control can be used in a voltage following mode by supplying an isolated analog input signal to terminal P2(+) and F-. The control is supplied with a 5 kΩ remote potentiometer and QD terminals.

FEATURES:

• Plug-in Horsepower Resistor®5 – Eliminates the need to calibrate control for IR Comp and Current Limit when used on various horsepower motors.
• Auto Inhibit® – Allows the control to be rapidly switched “on” and “off” using the AC line.
• Inhibit and Enable – Allows the control to be turned “on” and “off” using electronic switching.
• Trimpots: MIN & MAX Speed, IR Comp, Current Limit, ACCEL & DECEL
• Armature or Tach-Generator Feedback
• MOV Transient Protection
• SMT Construction
• Power On and Current Limit LED Indicators
• Built-in Armature and AC Line Fusing
• Main Speed Potentiometer (5 kΩ) (included)

SPECIFICATIONS: 

Speed Range (Ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  50:1
Load Regulation – Armature Feedback
(0 – Full Load, 50:1 Speed Range) (% Base Speed) . . . . . . . . . . . . . . . . . . . 1*
Load Regulation – Tachometer Feedback
(0 – Full Load, 50:1 Speed Range) (% Set Speed) . . . . . . . . . . . . . . . . . . . . . 1*
Line Voltage Regulation (at Full Load, ± 10% Line Variation) (% Speed) 1/2*
Control Linearity (% Speed vs. Dial Rotation) . . . . . . . . . . . . . . . . . . . . . . . . . .2
CL/Torque Range (% Full Load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  0 – 200
ACCEL-DECEL Time Range (0 – Full Speed) (Secs.) . . . . . . . . . . . . 0.2 – 10
MIN Speed Trimpot Range (% Full Speed) . . . . . . . . . . . . . . . . . . . . . . . .0 – 30*
MAX Speed Trimpot Range (% Full Speed) . . . . . . . . . . . . . . . . . . . . . 50 – 120*
IR Compensation Trimpot Range (at Specified Full Load) (Volts) . . . .0 – 24
Maximum Allowable Ambient Temperature (at Full Rating) (°C/°F) . . 45/113
Tach Feedback Input Volts (Per 1000 RPM) (VDC) . . . . . . . . . . . . . . . . . . .7/50

Notes: 1. Rating indicated is with Auxiliary Heat Sink. For maximum rating without Auxiliary Heat Sink see Electrical Ratings Chart. 2. Short circuit protected at motor only. 3. KB Limited Warranty applies. 4. CE compliance requires KBRF-200A RFI Filter and proper wiring practices. 5. Fuses and Plugin Horsepower Resistor® 

Optional Accessories: 

• Auxiliary Heat Sink (Part No. 9861) – Doubles the horsepower rating of the control
• Barrier Terminal Board (Part No. 9897) – Converts the quick-connect terminals of the KBMM™ to a barrier terminal block. Contains PC board mounted line and armature fuse holders. Plugs onto the quick-connect terminals of the KBMM
• SI-6 Signal Isolator (Part No. 9444) – Provides isolation between nonisolated signal sources and the KBMM™. Plugs onto the quick-connect terminals of the KBMM™. Contains barrier terminal block.
• Run/Brake Module (Part No. 9952) – Used for applications that require rapid stopping of the motor. Contains barrier terminal block
• Barrier Terminal Accessory Kit (Part No. 9883) – When used with the Auxiliary Heat Sink, it converts the quick-connect terminals of the KBMM™ to a barrier terminal block and provides built-in fusing.
• Dial Plate and Knob Kit (Part No. 9832) – Provides indication of the Main Speed Potentiometer position (incremented form 0 – 100%).
• Finger-Safe Cover (Part No. 9564) – Converts the control from open chassis to the IP-20 standard. (Fuse holders must be removed when installing the Finger-Safe Cover.)
• DIN Rail Mounting Kit (Part No. 9995)
• RFI Filters – A variety of filters are available in both undermount and remote designs. The filters comply with CE Directive 89/336/EEC relating to the EMC Class A Industrial, Class B Residential and FCC A and B. See RFI Filters and Chokes Selection Guide D-321.